Product Overview
AMX NMX-ENC-N1115-WP SVSI Wallplate Minimal Compression Video Over IP Encoder
The NMX-ENC-N1115-WP encoder offers an affordable local AV over IP switching solution in a convenient 2-gang Décor-style wallplate. It packetizes video into a minimally compressed IP format for excellent video quality at low latencies and is perfect for point-to-point video distribution.
The encoder is easily mounted in a wall, lectern, or floor box using a standard 2-gang US back box and is connected to power and Ethernet via a single category cable.
AMX NMX-ENC-N1115-WP Includes:
- AMX NMX-ENC-N1115-WP SVSI Wallplate
AMX NMX-ENC-N1115-WP Features:
- Visually lossless Minimal Proprietary Compression (MPC) algorithm allied to all resolutions
- Combined encode and decode latency of 10ms at 60 fps
- Power over Ethernet (PoE) eliminates the need for a power supply
- Separate HDMI and VGA input connectors
- Wallplate form factor for easy and convenient installation is a wall, floor or lectern
AMX NMX-ENC-N1115-WP Specifications:
- Video:
- Digital Video Input: HDMI, DVI-D*, Dual-Mode DisplayPort (DP++)*
- Analog Video Input: HD-15 VGA, Component*
- Video Output: Video Output
- Formats: HDMI, DVI-D*, Dual-Mode DisplayPort (DP++)*, HDCP content protection support, RGBHV, YPbPr
- Progressive Input Resolutions
- Supports most common HD up to 1920x1200.
- Interlaced Input Resolutions
- Supports 1080i60.
- Analog Input Resolutions
- NOTE: Input resolutions supported @60Hz refresh rates are also supported @59.94Hz.
- Supports most common HD up to 1920x1200.
- Output Resolutions: Matched to inputs.
- Analog-To-Digital Conversion: 8-bit 165 MHz per each of three color channels
- NOTE: The N1115-WP does not accept Composite or S-Video (YC).
- Color Space: 4:2:2
- Audio:
- Input Signal Types: Embedded audio on HDMI (DVI-D through adapter) or Analog Stereo
- Output Signal Types: Ethernet
- Analog Audio Format: 8ch PCM, Stereo 2-channel
- Analog-To-Digital Conversion: 16-bit 32 kHz, 44.1 kHz and 48 kHz
- Latency:
- Latency: 10 ms at 60 fps
- Bandwidth: 840 Mb/s (varies with resolution)
- Comunications:
- Ethernet: 10/100/1000 Mbps, auto-negotiating, auto-sensing, full/half duplex, DHCP, Auto IP, and Static IP
- HDMI: HDCP, EDID management
- Ports:
- P0: 8-wire RJ45 female; 10/100/1000 Mbps 10/100/1000Base-T auto-sensing gigabit Ethernet switch port; Provides the network connection, network AV video, and power to the Encoders and Decoders
- HDMI IN: HDMI video input
- VGA IN: DB15 analog input
- USB IN - Host: USB-B host input
- USB IN - Maintenance: USB-Mini maintenance input
- Controls and Indicators - Front Panel
- RESET Button: Recessed pushbutton; Press to initiate a 'warm restart' causing the processor to reset, but not lose power. A reset does NOT affect the current settings
- POWER LED: On solid (green) when operating power is supplied (via PoE or local power supply)
- AUDIO LED: On (green) when audio is transmitting.
- ANALOG VIDEO LEDs: On (green) when analog source is available and transmitting.
- DIGITAL VIDEO LED: On (green) when video source is available and transmitting
- HDCP LED: On (green) when the source is using HDCP
- STREAM LED: On (green) when the unit is streaming video
- STATUS LED: Flashing (green) when the unit is active.
- LINK/ACT LED: Flashing (yellow) when network traffic is being sent or received.
- Power Supply:
- Power over Ethernet: Can be powered via a PoE switch or other equipment with a PoE source. Conforms to IEEE 802.3af Class 3 (802.3at Type 1); Point-to-point applications between the encoder and a decoder requires a PoE injector to power the wallplate encoder.
- Environmental:
- Temperature (Operating): 32° to 104°F (0° to 40°C)
- Temperature (Storage): -22° to 158°F (-30° to 70°C)
- Humidity (Operating): 10% to 90% RH (non-condensing)
- Humidity (Storage): 0% to 90% RH (non-condensing)
- Heat Dissipation: Up to ~26 BTU/hr
- General:
- Dimensions (HWD): 4.06" x 3.5" x 2.25" (10.31 cm x 8.84 cm x 5.72 cm)
- Weight: .75 lb (0.34 kg)
- Airflow: Natural convection via vent openings on front, back, and top
- Installation: Mounts onto standard 2 gang US back boxes; Mounts into standard décor style wallplates (not included)
- Regulatory Compliance: FCC, CE, and NTRL