Product Overview
Meyer Sound’s ULTRA-X20 self-powered full-range loudspeaker brings state-of-the-art ULTRA-X40 point-source technology to a smaller, lighter speaker that's ideal for any application where size and weight are critical factors. Whether used as a compact main system, as fills, or as surrounds in a larger system, the ULTRA-X20 delivers high power output, low distortion, and consistent polar response in any configuration. The XP configuration saves time and makes connection easier thanks to IntelligetDC technology that receives balanced audio and DC power from a single composite cable. The ULTRA-X20 measures just 7.5 inches wide by 19.04 inches high by 8.6 inches deep, delivering 123.5 dB peak SPL measured using M-Noise. It features two 5-inch cone drivers and a 2-inch compression driver in concentric configuration for more consistent pattern control below the crossover point. The X20's 110° x 50° rotatable horn produces precise, even coverage regardless of orientation, allowing you to cover any room with confidence.
Meyer Sound ULTRA-X20XP Applications:
- Multi-purpose Audio/Visual
- Corporate rental
- Houses of worship
- Conference rooms
- High-end private installations
- Retail spaces
- Theater
Meyer Sound ULTRA-X20XP Features:
- Internal 860 watt amplifier produces up to 123dB max SPL distortion-free audio
- 110° x 50° rotatable Constsnt-Q horn
- Built-in DSP, crossover, EQ, and more
- IntelligentDC technology receives balanced audio and DC power from a single composite cable
- Four M8 threaded rigging points
- 35mm pole mount, M20 threads
Meyer Sound ULTRA-X20XP Specifications:
- TRANSDUCERS
- Low Frequency: Two 5-inch cone drivers; 6 Ω nominal impedance
- High Frequency: One 2-inch diaphragm compression driver connected to a rotatable horn; 8 Ω nominal impedance
- AUDIO INPUT
- Type: Differential, electronically balanced
- Maximum Common Mode Range: ±15 V DC, clamped to earth for voltage transient protection Connectors: XLR 3-pin female input with male loop output; optional XLR 5-pin connectors to accommodate both balanced audio and RMS signals; XLR 3-pin TOP (Total Outdoor Protection) connectors on weather-protected units only.
- Input Impedance: 10 kΩ differential between pins 2 and 3
- Wiring: Pin 1: Chassis/earth through 1 kΩ, 1000 pF, 15 V clamp network to provide virtual ground lift at audio frequencies Pin 2: Signal + Pin 3: Signal – Pin 4: RMS (polarity insensitive) Pin 5: RMS (polarity insensitive) Case: Earth ground and chassis
- Nominal Input Sensitivity: 0 dBV (1.0 V rms) continuous is typically the onset of limiting for noise and music Input Level Audio source must be capable of producing of +20 dBV (10 V rms) into 600 Ω to produce the maximum peak SPL over the operating bandwidth of the loudspeaker.
- AMPLIFIER
- Type: Three-channel, Class-D
- Total Output Power5: 860 W peak
- THD, IM, TIM:
- Cooling: Convection
- PHYSICAL
- Dimensions W: 7.44 in (189 mm) x H: 19.04 in (484 mm) x D: 8.66 in (220 mm)
- Weight: 27 lb (12.3 kg)
- Enclosure: Aluminum with slightly textured black finish
- IP Rating: Weather-protected version rated IP54 with properly installed rain hood. See the ULTRA-X20XP Operating Instructions available at meyersound.com/documents for details.
- Protective Grille: Powder-coated, round-perforated steel
- Rigging: Two integrated M8 threaded points on each end; optional accessories for various rigging options (see accessories section); four M6 threaded holes with 5-inch by 2.75-inch (127 mm by 70 mm) hole pattern on the rear for use with third-party wall mounts.
