Meyer Sound MM-10XP-5 10" Active Subwoofer, 5-Pin Input

The MM‑10 miniature subwoofer delivers expanded low frequency for applications that require excellent audio quality from a compact system. Designed primarily as a companion to Meyer Sound's MM‑4XP miniature loudspeaker, as well as the UP‑4XP ultra-compact loudspeaker, both with IntelligentDC technology, the MM‑10 allows system designers to create full-range systems where space limitations are a concern.

The MM‑10 features an operating frequency range of 33Hz to 228Hz with a conservatively rated maximum peak SPL of 123dB. The MM‑10 bass reflex cabinet houses a single 10-inch driver and a single-channel power amplifier complete with onboard processing, including a crossover, driver protection, and frequency and phase correction. The built-in crossover accepts full-range signals, facilitating basic daisy-chaining for signal distribution, eliminating the need for external

Applications:

° Background music

° Small theatres

° Portable AV systems

° Compact voice reinforcement systems

Features:

• Powerful low-frequency response from a very small cabinet
• Low distortion affords exceptionally clean bass
• Adaptable to complement MM‑4XP and UP‑4XP loudspeakers
• Versions include external IntelligentDC power supply or built-in AC power for driving satellite loudspeakers

Specifications:

• Operating Frequency Range: 33Hz – 228Hz
• Frequency Response: 35Hz – 208Hz ±4dB
• Phase Response: 38Hz – 138Hz ±45°
• Maximum Peak SPL: 123dB
• Dynamic Range: less than 100dB
• Coverage: 360°
• Transducer
  • Type: 10-inch cone driver
  • Nominal Impedance: 4Ω
  • Voice Coil Size: 2 inches
  • Power Handling: 400W (AES)
• Audio Input
  • Type: Differential, electronically balanced
  • Maximum Common Mode Range: ±5VDC
  • Input Impedance: 10kΩ electronically balanced
  • DC Blocking: 4.8Hz high pass
  • CMRR: < –60dB, typically < –72dB (200Hz – 3kHz)
  • RF Filter
    • Common mode: 616kHz
    • Differential mode: 616kHz
  • Nominal Input Sensitivity –2.0dBV (0.8V rms) continuous is typically the onset of limiting for noise and music
  • Input Level
  • Audio source must be capable of producing +16dBV (6.3V rms, 9.0V peak) into 600Ω to produce the maximum peak SPL over the operating bandwidth of the loudspeaker
• Amplifier
  • Type: Class D
  • Output Power: 220W
  • Total Output: 440W peak
  • THD, IM, TIM < .02%
  • Load Capacity: 4Ω
  • Cooling: Convection
• MM-10XP Rear Panel
  • Audio/Power Connector
    • Phoenix 5-pin male or EN3 5-pin male (two pins for DC power, three pins for balanced audio)
  • Wiring
    • Pin 1: DC power negative (–)
    • Pin 2: DC power positive (+)
    • Pin 3: Balanced audio shield, chassis/earth
    • Pin 4: Balanced audio (–)
    • Pin 5: Balanced audio (+)
  • Input Polarity Switch: Reverses audio input polarity between pins 4 and 5
  • LED: Displays loudspeaker status
  • MM-10XP DC Power
    • Safety Agency Rated Operating Range: 48VDC
    • Current Draw:
    • Idle Current: 0.16A rms
    • Max. Long-Term Continuous Current (>10 sec): 0.90A rms
    • Burst Current: 2.5A rms
    • Ultimate Short-Term Peak Current: 3.0A peak
    • Inrush Current < 7.0A peak
  • MPS-488HP IntelligentDC Power Supply Required For information and specifications for the Meyer Sound MPS-488HP IntelligentDC external power supply, refer to its datasheet